Glass Sintering Technology

Glass Sintering Technology
The glass sintering technology can be applied on the connectors because of the well airtight performance, high temperature resistance, and cost-effective. The hermetic sealing connectors can be used widely for the connections between hermitic sealed packages. These connectors could be used for aerospace industry, satellite communications, and military applications.

 

Surge Arrester

Frontlynk Surge Arrester series are using for N and 7/16 type.
High Performance from DC to 3 GHz, and 2 to 6 GHz.

 

High Performance Adaptor DC to 67GHz

High Performance Adaptor, N to N and N to SMA series. Up to 18 GHz well-perform VSWR. 1.0mm to 1.85mm adaptors.

 

1.0mm connectors DC to 110GHz

The 1.0 mm connectors are designed for 50 Ohms, excellent performance up to 110 GHz . The 1.0 mm connectors outer conductor ID is 1.0 mm, the interface is air dielectric with the contact supported by a short dielectric bead.
The Frontlynk 1.0 mm connector series is for semi-rigid and low-loss flexible cable, adaptor for custom applications. These cable assemblies realize low insertion loss, low reflection loss and well-perform VSWR.

 

1.85mm Connectors DC to 67GHz

The connector outer conductor ID is 1.85 mm, and OD is 4.7 mm, allowing compatibility, so that the 1.85mm connector mates with the 2.4mm connector and has the same ruggedness. It’s a 50 Ohms connector with performance up to 67 GHz.

   

2.4mm Connectors DC to 50GHz

The 2.4mm series was designed to eliminate the fragility of the SMA and 2.92mm connectors by increasing the outer wall thickness and strengthening the female fingers.
The outer contact ID is 2.4 mm, and OD is 4.7mm.
The performance is up to 50 GHz.

   

2.92mm Connectors DC to 40GHz

The 2.92mm series was designed with highly rugged physical interfaces in mind that would mate with 3.5mm and SMA dimensions. The 2.92mm series use an air dielectric, with the performance up to 40 GHz. The outer contact ID is 2.92 mm, and OD is 4.55 mm.

   

3.5mm Connectors DC to 34GHz

The 3.5mm series was designed with highly rugged physical interfaces in mind that would mate with SMA dimensions, allowing thousands of repeatable connections. The performance is up to 34 GHz.

   

SMPM Connectors DC to 65GHz

The SMPM connectors are 20% smaller to SMP connectors and have frequency ranges up to 65 GHz. The SMPM connectors were developed to fit for smaller and higher frequency connectors than the SMP.

 

SMP Connectors DC to 40GHz

Frontlynk developed the SMP series to fulfill the customer's demands for higher-frequency and miniaturized connectors.
These are easy snap-on connectors; operatible up to 40 GHz.

   

SSMA Connectors DC to 18GHz

SSMA connectors are micro-miniature, high-frequency connectors with threaded mating (smaller version of SMA series), designed to MIL-PRF-39012 requirements.

   

SMA Connectors DC to 18GHz

SMA connectors are subminiature units designed to provide high electrical performance for microwave applications up to 18 GHz.

   

7/16 Connectors DC to 7.5GHz

The 7/16 series connectors are applied to communication systems with high power. With the design of 50 Ohm impedance and remarkable performance up to 7.5 GHz.

   

BNC Connectors DC to 4GHz

BNC connectors are characterized by their 2-stud quick disconnect bayonet lock coupling arrangement. They are suitable for a wide range of systems, including radio telecommunication systems, medical equipment, computer network and test instrumentation.

   

N Connectors DC to 11GHz

N connectors are medium size, high quality connectors with a coupling screw system designed for use at frequencies up to 11 GHz.

   

TNC Connectors DC to 10GHz

TNC connectors are designed with a highly reliable threaded coupling to ensure additional protection against shocks and vibrations.

   

1.0/2.3 Connectors DC to 4GHz

1.0/2.3 connectors feature a slide-on coupling mechanism to prevent accidental disconnection.
The 1.0/2.3 series is suitable for applications up to 4 GHz and especially ideal for telecommunication systems.

   

BMA Connectors DC to 18GHz

BMA series is an easy use slide-on connector, has 50 Ohms impedance and is suitable for high performance microwave applications up to 18 GHz.

   

FAKRA Connectors DC to 4GHz

To cope with growth demands in telematics and multimedia applications for modern automobile, Automotive Industries created a high-performing, cost-effective RF connector based on the FAKRA and USCAR standards.

   

MCX Connectors DC to 6GHz

MCX miniature snap-on connectors have 50 ohms impedance structure operates in a frequency range up to 6 GHz.
MCX series is ideal for applications of GPS, wireless communication and test instrumentation.

   

MMCX Connectors DC to 6GHz

MMCX series is intended for use in applications where the smallest dimensions have to be achieved.

   

SMB Connectors DC to 4GHz

SMB series is a semi-precision and subminiature device that provides repeatable electrical performance to 4 GHz.
SMB family of connectors provides a means of quick connect/disconnect through a snap-on type coupling.

   

F Connectors DC to 3GHz

F series is economically priced connectors specially designed for use with NTSC TV ANTENNA and other similar applications.

   



Copyrightc2009 Frontlynk All rights reserved. Powered by Subkarma
Tel:+886-6-356-2626    Fax:+886-6-356-6268
Online: 1